Ports | 20x 1G SFP, 4x 1G RJ45/SFP Combo, 4x 10G SFP+ |
Power Device | 2x Power Supplies – Internal |
Forwarding Rate | 95 Mpps |
Jumbo Frame | 9KB |
Flash Memory | 64MB |
Stackability | Up to 6 Units (Same Models) |
MTBF (Hours) | >100,000 |
Switch Chip | Broadcom BCM56151 |
Switching Capacity | 128 Gbps |
MAC Address | 16K |
DRAM | 128MB |
DDRIII Capacity | 512MB |
Acoustic Noise | 52dB |
Stackable Managed Ethernet Switch – S3900-24F4S
Get Stackable Managed Ethernet Switch – S3900-24F4S at the best market-competitive price with ready to ship availability.
Condition: New
Power Device: 2x Power Supplies – Internal
In Stock – Ready to Ship
Related products
- Switches
Cisco Catalyst Compact 2960C-8TC-L Switch 8 Ports Managed-Desktop
0 out of 5(0)Main Specifications: Device Type Switch – 8 ports – Managed Enclosure Type Desktop, rack-mountable, wall-mountable 1U Interfaces Fast Ethernet Ports 8 x 10/100 + 2 x shared Gigabit SFP Performance Forwarding performance : 10 GbpsForwarding performance (64-byte packet size) : 3.8 Mpps Capacity Virtual interfaces (VLANs) : 255 Jumbo Frame Support 9018 Routing Protocol RIP-1, RIP-2 Remote Management Protocol SNMP 1, SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, CLI Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.1ae, IEEE 802.1ab (LLDP) Power AC 120/230 V ( 50/60 Hz ) Dimensions (WxDxH) 26.9 cm x 21.3 cm x 4.4 cm Weight 1.08 kg Manufacturer Warranty Limited lifetime warranty General Device Type Switch – 8 ports – Managed Enclosure Type Desktop, rack-mountable, wall-mountable – 1U Subtype Fast Ethernet Ports 8 x 10/100 + 2 x shared Gigabit SFP Performance Forwarding performance : 10 GbpsForwarding performance (64-byte packet size) : 3.8 Mpps Capacity Virtual interfaces (VLANs) : 255 Jumbo Frame Support 9018 Routing Protocol RIP-1, RIP-2 Remote Management Protocol SNMP 1, SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, CLI Authentication Method Kerberos, Secure Shell (SSH), RADIUS, TACACS+ Features DHCP support, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, Syslog support, DiffServ support, Broadcast Storm Control, IPv6 support, Multicast Storm Control, Unicast Storm Control, Spanning Tree Protocol (STP) support, DHCP snooping, Dynamic Trunking Protocol (DTP) support, Port Aggregation Protocol (PAgP) support, Trivial File Transfer Protocol (TFTP) support, Access Control List (ACL) support, Quality of Service (QoS), Dynamic ARP Inspection (DAI), STP Root Guard, Uni-Directional Link Detection (UDLD), fanless, DHCP relay, Link Aggregation Control Protocol (LACP), Remote Switch Port Analyzer (RSPAN) Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.1ae, IEEE 802.1ab (LLDP) RAM 128 MB Flash Memory 64 MB Status Indicators Port status, link activity, system Expansion / Connectivity Interfaces 2 x 10Base-T/100Base-TX/1000Base-T – RJ-458 x 10Base-T/100Base-TX – RJ-451 x console – mini-USB Type B – management1 x RS-232 – RJ-45 – management2 x SFP (mini-GBIC)1 x USB – Type A Power Power Device Internal power supply Voltage Required AC 120/230 V ( 50/60 Hz ) Miscellaneous MTBF 516,980 hours Compliant Standards GOST, CISPR 24, EN55022, VCCI Class A ITE, EN55024, CISPR 22, CCC, RoHS, UL 60950-1, IEC 60950-1, EN 60950-1, CSA C22.2 No. 60950-1, GB 4943 Software / System Requirements Software Included Cisco IOS LAN Base Dimensions & Weight Width 26.9 cm Depth 21.3 cm Height 4.4 cm Weight 1.08 kg Manufacturer Warranty Service & Support Limited lifetime warranty Service & Support Details Limited warranty – replacement – lifetime – response time: next business dayLimited warranty – power supply – 5 years Environmental Parameters Min Operating Temperature -5 °C Max Operating Temperature 40 °C Humidity Range Operating 5 – 95% (non-condensing) Min Storage Temperature -25 °C Max Storage Temperature 70 °C Humidity Range Storage 5 – 95% (non-condensing) Brief Overview Catalyst 2960-C Series 8 ports Gigabit SFP Desktop Rack-mountable, Wall-mountable 1U Fast Ethernet RJ-45 Cisco IOS LAN Base Cisco Catalyst Compact 2960C-8TC-L Switch comes with a Forwarding performance of the order of 10 Gbps. The 64-byte packet size in this device is forwarded at the rate of 3.8 Mpps. It is an 8 port device and can handle 255 virtual LANs as well. This device has a 9018 jumbo support frame. Some of the other impressive features of this device include DHCP support, DiffServ support, Broadcast Storm Control, IPv6 support, Multicast Storm Control, Unicast Storm Control, Spanning Tree Protocol (STP) support and much more. The dimensions of this product are 10.6 in x 8.4 in x 1.7 in. Cisco Catalyst 2960-C Series Overview: Cisco Catalyst compact switches easily extend an intelligent, fully managed Cisco Catalyst wired switching infrastructure, including end-to-end IP and Borderless Network services, with a single Ethernet cable or fiber from the wiring closet. These attractive, small form-factor Gigabit and Fast Ethernet switches are ideal for connecting multiple devices on the retail sales floor and in classrooms, hotels, and factories and for extending wireless LAN networks: wherever space is at a premium and multiple cable runs could be challenging. Cisco Catalyst 2960-C Series Compact Switches highlights: Extend a highly secure, intelligent, managed Cisco Catalyst infrastructure with a single Ethernet cable or fiber from the wiring closet Support for advanced security and services, including voice, video, and Cisco Borderless Network services, to remote endpoints Power over Ethernet (PoE) pass-through enables the compact switch to draw power from the wiring closet and pass it to end devices (selected models) Attractive, small form factor and fanless operation fit in confined spaces where multiple cable runs could be challenging Easy to deploy, manage and extend the network loop free Enhanced limited lifetime hardware warranty Cisco Catalyst 2960-C Series Software Cisco Catalyst 2960-C Series compact switches ship with the LAN Base version of Cisco IOS Software, as available on other Cisco Catalyst 2960 Series Switches. Similarly, Cisco Catalyst 3560-C compact switches ship with the IP Base version of Cisco IOS Software, as with other 3560 Series switches. Neither series of compact switches can be upgraded. Cisco Catalyst 2960-C switches deliver advanced Layer 2 switching with intelligent Layer 2 through 4 services for the network edge, such as voice, video, and wireless LAN services. The IP Base feature set on Cisco Catalyst 3560-C switches adds baseline enterprise services, including support for routed access, Cisco TrustSec, media access control security (MACsec), and other Cisco Borderless Network services. The LAN Base feature set offers enhanced intelligent services that include comprehensive Layer 2 features. The IP Base feature set provides baseline enterprise services in addition to all LAN Base features. IP Base also includes the support for routed access, MACsec, and Open Shortest Path First (OSPF). Cisco Compact Switches Extend Enterprise Networks Enterprises often look to extend the reach of their networks – to bring wired connectivity to more employees and to support new wireless deployments. Running additional Ethernet cables for individual devices might be impractical, but the same security, services, and management must be supported. Cisco Catalyst 2960-C Series compact switches extend the wired Cisco access infrastructure, 8 or 12 ports at a time, with a single Ethernet cable or fiber, all while delivering the same services as the Cisco Catalyst switches in the wiring closet. PoE, quiet operation, and flexible mounting options allow placement in confined spaces. Cisco Networked Sustainability: Good for Business, Better for Environment Cisco EnergyWise is an innovative architecture, added to the Cisco Catalyst 2960-C Series compact switches, that enables the measurement of power consumption in the network infrastructure and network-attached devices. EnergyWise encompasses a highly intelligent network-based approach to communicate messages that measure and control energy between network devices and endpoints. The network discovers Cisco EnergyWise-manageable devices, monitors their power consumption, and takes action based on business rules to reduce power consumption. Efficient switch operation: Cisco Catalyst 2960-C Series compact switches use hardware components created by Cisco providing optimum power saving, low-power operations for industry best-in-class power management, and power consumption capabilities. Borderless Security The Cisco Catalyst compact switches provide superior Layer 2 threat defense capabilities for mitigating man-in-the-middle attacks (such as MAC, IP, and ARP spoofing). TrustSec, a primary element of Borderless Security Architecture, helps enterprise customers secure their networks, data and resources with policy-based access control, identity and role-aware networking, pervasive integrity, and confidentiality. The borderless security is enabled by the following feature sets in the Cisco Catalyst 2960-C Series compact switches: Threat defense Cisco TrustSec Other advanced security features Threat Defense Cisco Integrated Security Features are an industry-leading solution available on Cisco Catalyst switches that proactively protects your critical network infrastructure. Delivering powerful, easy-to-use tools to effectively prevent the most common and potentially damaging Layer 2 security threats, Cisco Integrated Security Features provide robust security throughout the network. Cisco Integrated Security Features include Port Security, DHCP Snooping, Dynamic ARP Inspection, and IP Source guard. Port Security secures the access to an access or trunk port based on MAC address. It limits the number of learned MAC addresses to deny MAC address flooding. DHCP Snooping prevents malicious users from spoofing a DHCP server and sending out bogus addresses. This feature is used by other primary security features to prevent a number of other attacks such as ARP poisoning. Dynamic ARP Inspection (DAI) helps ensure user integrity by preventing malicious users from exploiting the insecure nature of the ARP protocol. IP source guard prevents a malicious user from spoofing or taking over another user’s IP address by creating a binding table between the client’s IP and MAC address, port, and VLAN. Cisco TrustSec TrustSec secures access to the network, enforces security policies, and delivers standard-based security solutions such as 802.1X enabling secure collaboration and policy compliance. TrustSec capabilities reflect Cisco thought leadership, innovations, and commitment to customer success. These new capabilities include: IEEE 802.1AE MACsec with prestandard 802.1X-REV Key management: industry’s first fixed switches with prestandard 802.1X-Rev key management. Available on Cisco Catalyst 3560-C Series Switches, MACsec provides Layer 2, line rate Ethernet data confidentiality and integrity on host facing ports, protecting against man-in-the-middle attacks (snooping, tampering, and replay). Flexible authentication that supports multiple authentication mechanisms including 802.1X, MAC Authentication Bypass, and web authentication using a single, consistent configuration. Open mode that creates a user friendly environment for 802.1X operations. Integration of device profiling technology and guest access handling with Cisco switching to significantly improve security while reducing deployment and operational challenges. RADIUS Change of Authorization and Downloadable ACLs for comprehensive policy management capabilities. 802.1X Supplicant with Network Edge Access Transport (NEAT) enables extended secure access where compact switches in the conference rooms have the same level of security as switches inside the locked wiring closet. Other Advanced Security Features Other Advanced Security features include but are not limited to: Private VLAN Edge provides security and isolation between switch ports, which helps ensure that users cannot snoop on other users’ traffic. Multidomain Authentication allows an IP phone and a PC to authenticate on the same switch port while placing them on appropriate voice and data VLAN. Port-Based ACLs for Layer 2 interfaces allow security policies to be applied on individual switch ports. Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3 (SNMPv3) provide network security by encrypting administrator traffic during Telnet and SNMP sessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic software image because of U.S. export restrictions. Bidirectional data support on the Switched Port Analyzer (SPAN) port allows Cisco Intrusion Detection System (IDS) to take action when an intruder is detected. TACACS+ and RADIUS Authentication facilitates centralized control of the switch and restricts unauthorized users from altering the configuration. MAC Address Notification allows administrators to be notified of users added to or removed from the network. Multilevel Security on Console Access prevents unauthorized users from altering the switch configuration. Bridge Protocol Data Unit (BPDU) Guard shuts down Spanning Tree PortFast-enabled interfaces when BPDUs are received to avoid accidental topology loops. Spanning Tree Root Guard (STRG) prevents edge devices not in the network administrator’s control from becoming Spanning Tree Protocol root nodes. Dynamic VLAN Assignment is supported through implementation of VLAN Membership Policy Server client capability to provide flexibility in assigning ports to VLANs. Dynamic VLAN facilitates the fast assignment of IP addresses. Cisco Borderless Networks and Access Switching Borderless Networks, a Cisco next-generation architecture, deliver the new workspace experience, connecting anyone, anywhere, using any device, to any resource – securely, reliably, transparently. The Cisco Borderless Networks architecture addresses primary IT and business challenges to help create a truly borderless experience by bringing interactions closer to the employee and customer. Innovations in switching help organizations deliver ease of operation, green efficiency, security, and performance to accelerate the way IT delivers and scales those services on the network. Cisco Compact Switches for Education Video and distance learning applications have become a common part of the curriculum for K-12 and higher education. Support for IP phones and secure wired and wireless connectivity in the classroom are also common requirements. Yet schools and universities must often work within limited budgets and aging facilities, making wiring runs from a central point in the building to multiple devices in the classroom cost prohibitive. Cisco Catalyst compact switches extend fully managed IP services to the classroom with a single Ethernet cable or fiber. Quiet operation and flexible mounting options make them ideally suited for classrooms or confined areas nearby. Cisco Compact Switches Extend Enterprise Networks Enterprises often look to extend the reach of their networks – to bring wired connectivity to more employees and to support new wireless deployments. Running additional Ethernet cables for individual devices might be impractical, but the same security, services, and management must be supported. Cisco Catalyst 2960-C Series compact switches extend the wired Cisco access infrastructure, 8 or 12 ports at a time, with a single Ethernet cable or fiber, all while delivering the same services as the Cisco Catalyst switches in the wiring closet. PoE, quiet operation, and flexible mounting options allow placement in confined spaces. Cisco Enhanced Limited Lifetime Hardware Warranty Cisco Catalyst 2960-C Series Switches come with an enhanced limited lifetime hardware warranty that includes 90 days of Cisco Technical Assistance Center (TAC) support and next-business-day hardware replacement free of change.
SKU: WS-C2960C-8TC-L - Switches
Cisco Catalyst 6506-E Switch Desktop
0 out of 5(0)Main Specifications: Product Description Cisco Catalyst 6506-E – switch – desktop Device Type Switch Enclosure Type Desktop Dimensions (WxDxH) 17.5 in x 18.2 in x 19.2 in Weight 50 lbs General Device Type Switch Enclosure Type Desktop Expansion / Connectivity Expansion Slots 6 (total) / 6 (free) x expansion slot Installed Modules Qty (Max) 0 (installed) / 6 (max) Miscellaneous Compliant Standards NEBS level 3, FCC Class A certified, VCCI, EN 60950, EN55022, UL 1950, IEC 825-1/EN 60825-1 class 1, IEC 60950, EN55024, CISPR 22, CSA 22.2 No. 60950, ACA TS001, AS/NZS 3260, FCC Part 15, AS/NZS 3548 Dimensions & Weight Width 17.5 in Depth 18.2 in Height 19.2 in Weight 50 lbs Environmental Parameters Min Operating Temperature 32 °F Max Operating Temperature 104 °F Humidity Range Operating 10 – 90% Brief Overview 6500 Switches Desktop 48-port Multigigabit network security The WS-C6506-E-FAN is the fan tray for the improved WS-C6506E chassis by industry leader Cisco Systems. The six-slot WS-C6506E chassis is designed to scale beyond 4000W power supply configurations. Cisco is the worldwide leader in networking for the Internet. Cisco offers the broadest line of solutions for transporting data, voice and video within buildings, across campuses, or around the world. Cisco solutions ensure that networks both public and private operate with maximum performance, security, and flexibility. Cisco Catalyst 6500 Series Chassis Overview: Cisco introduces the Cisco Catalyst 6500 Enhanced Series Chassis (6500-E Series) delivering up to 2 terabits per second of system bandwidth capacity and 80 Gbps of per-slot bandwidth. In a system configured for VSS, this translates to a system capacity of 4 Tbps. The Cisco Catalyst 6500 Enhanced Series Chassis will be capable of delivering up to 180 Gbps of per-slot bandwidth with a system capacity of up to 4 terabits per second. A system configured for VSS will be capable of delivering up to 8 Tbps of system bandwidth. The Cisco Catalyst 6500-E Series Switch offers the broadest range of interface modules with industry-leading performance and advanced feature integration. The Cisco Catalyst 6500-E Series Switch also offers high port densities and comes in 3-, 4-, 6-, 9, 9-Vertical, and 13-slot versions that make it ideal for a range of deployment scenarios. The Cisco Catalyst 6500-E Series Chassis provides superior investment protection by supporting multiple generations of products in the same chassis, lowering the total cost of ownership. The Cisco Catalyst 6500-E Series Chassis supports all the Cisco Catalyst 6500 Supervisor Engines up to and including the Cisco Catalyst 6500 Series Supervisor Engine 2T, and associated LAN, WAN, and services modules. Applications The versatile Cisco Catalyst 6500-E Series Chassis is ideal for addressing high-performance, high- port-density Fast Ethernet, Gigabit Ethernet, and 10 and 40 Gigabit Ethernet applications in all parts of the network. This series is ideally suited for enterprise core and aggregation environments. The Cisco Catalyst 6500-E Series chassis offers industry-leading 10/100/1000 Gigabit Ethernet, 10 Gigabit Ethernet and 40 Gigabit Ethernet port densities while providing high levels of network resilience.
SKU: WS-C6506-E - Switches
Cisco CAT WS-C2960XR-48FPS-I 48 Port Full POE+ 4 SFP Uplinks IP Lite 740W
0 out of 5(0)Main Specifications: Product Description Cisco Catalyst 2960XR-48FPS-I – switch – 48 ports – managed – desktop, rack-mountable Device Type Switch – 48 ports – L3 – managed – stackable Enclosure Type Desktop, rack-mountable 1U Subtype Gigabit Ethernet Ports 48 x 10/100/1000 (PoE+) + 4 x SFP Power Over Ethernet (PoE) PoE+ PoE Budget 740 W Performance Switching capacity : 216 Gbps Forwarding performance : 107.1 Mbps Capacity Virtual interfaces (VLANs) : 1023 Jumbo Frame Support 9216 Routing Protocol OSPF, RIP-1, RIP-2, HSRP, VRRP, PIM-SM, PIM-DM, PIM-SSM, policy-based routing (PBR), RIPng Remote Management Protocol SNMP 1, SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, SSH, CLI Features Layer 2 switching, auto-negotiation, ARP support, Cisco Fast EtherChannel, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, Broadcast Storm Control, IPv6 support, Multicast Storm Control, Unicast Storm Control, Rapid Spanning Tree Protocol (RSTP) support, Multiple Spanning Tree Protocol (MSTP) support, DHCP snooping, Dynamic Trunking Protocol (DTP) support, Port Aggregation Protocol (PAgP) support, Trivial File Transfer Protocol (TFTP) support, Access Control List (ACL) support, Quality of Service (QoS), RADIUS support, MLD snooping, Dynamic ARP Inspection (DAI), Uni-Directional Link Detection (UDLD), Shaped Round Robin (SRR), Link Aggregation Control Protocol (LACP), Remote Switch Port Analyzer (RSPAN), layer 3 load balancing, Per-VLAN Rapid Spanning Tree (PVRST), Energy Efficient Ethernet, Multicast VLAN Registration (MVR), Strict Priority Queuing (SPQ), Class of Service (CoS) Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ab (LLDP), IEEE 802.3at, IEEE 802.3az Power AC 120/230 V ( 50/60 Hz ) Power Redundancy Yes Dimensions (WxDxH) 17.5 in x 16.1 in x 1.8 in Weight 14.8 lbs Manufacturer Warranty Limited lifetime warranty Extended Specifications General Device Type Switch – 48 ports – L3 – managed – stackable Enclosure Type Desktop, rack-mountable – 1U Subtype Gigabit Ethernet Ports 48 x 10/100/1000 (PoE+) + 4 x SFP Power Over Ethernet (PoE) PoE+ PoE Budget 740 W Performance Switching capacity : 216 Gbps Forwarding performance : 107.1 Mbps Capacity Virtual interfaces (VLANs) : 1023 Jumbo Frame Support 9216 Max Units In A Stack 8 Routing Protocol OSPF, RIP-1, RIP-2, HSRP, VRRP, PIM-SM, PIM-DM, PIM-SSM, policy-based routing (PBR), RIPng Remote Management Protocol SNMP 1, SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, SSH, CLI Authentication Method Secure Shell (SSH), RADIUS, TACACS+ Features Layer 2 switching, auto-negotiation, ARP support, Cisco Fast EtherChannel, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, Broadcast Storm Control, IPv6 support, Multicast Storm Control, Unicast Storm Control, Rapid Spanning Tree Protocol (RSTP) support, Multiple Spanning Tree Protocol (MSTP) support, DHCP snooping, Dynamic Trunking Protocol (DTP) support, Port Aggregation Protocol (PAgP) support, Trivial File Transfer Protocol (TFTP) support, Access Control List (ACL) support, Quality of Service (QoS), RADIUS support, MLD snooping, Dynamic ARP Inspection (DAI), Uni-Directional Link Detection (UDLD), Shaped Round Robin (SRR), Link Aggregation Control Protocol (LACP), Remote Switch Port Analyzer (RSPAN), layer 3 load balancing, Per-VLAN Rapid Spanning Tree (PVRST), Energy Efficient Ethernet, Multicast VLAN Registration (MVR), Strict Priority Queuing (SPQ), Class of Service (CoS) Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ab (LLDP), IEEE 802.3at, IEEE 802.3az Processor 1 x ARM : 600 MHz RAM 512 MB Flash Memory 128 MB Status Indicators Port status, link activity, port transmission speed, port duplex mode, system Expansion / Connectivity Interfaces 48 x 10Base-T/100Base-TX/1000Base-T – RJ-45 – PoE+ 4 x SFP (mini-GBIC) 1 x USB – Type A 1 x USB – Type B 1 x console – RJ-45 1 x management (LAN) – RJ-45 Power Power Device Internal power supply – hot-plug Installed Qty 1 (installed) / 2 (max) Power Redundancy Yes Power Redundancy Scheme 1+1 Power Provided 1025 Watt Voltage Required AC 120/230 V ( 50/60 Hz ) Miscellaneous MTBF 230,860 hours Compliant Standards CISPR 22 Class A, BSMI CNS 13438 Class A, CISPR 24, EN 61000-3-2, EN 61000-3-3, EN55024, EN55022 Class A, CB, ICES-003 Class A, RoHS, EN300-386, IEC 60950-1, EN 60950-1, UL 60950-1 Second Edition, FCC Part 15 A, CSA C22.2 No. 60950-1, VCCI Class A, KN22, KN24 Software / System Requirements Software Included Cisco IOS IP Lite Dimensions & Weight Width 17.5 in Depth 16.1 in Height 1.8 in Weight 14.8 lbs Manufacturer Warranty Service & Support Limited lifetime warranty Service & Support Details Limited warranty – lifetime Environmental Parameters Min Operating Temperature 23 °F Max Operating Temperature 113 °F Humidity Range Operating 10 – 95% (non-condensing) Min Storage Temperature -13 °F Max Storage Temperature 158 °F Humidity Range Storage 10 – 95% (non-condensing) Brief Overview Catalyst 2960-XR Series 48 Ports Switch Managed Cisco IOS IP Lite Desktop, Rack-mountable 1U PoE+ Gigabit Ethernet All of the models in the line of Catalyst 2960-X Series use similar technology. the integration of the Cisco IOS software image enables the module to be able to configure to the LAN Lite, LAN Base, or IP Lite feature set found in the model. The switch is useful for all sizes of network systems including small and large business networks and smaller classroom and hotel systems. It is easy to incorporate into any system. LAN Lite models have abridged functionality. This makes these model especially suited for smaller situations and uses. All models function through the basic requirements. Note: This switch model is compatible at a specific feature level i.e.: LAN Lite cannot be upgraded to LAN Base and LAN Base cannot be upgraded to IP Lite. Cisco Catalyst 2960-X Series Overview: Cisco Catalyst 2960-X Series Switches are fixed-configuration, stackable Gigabit Ethernet switches that provide enterprise-class access for campus and branch applications. Designed for operational simplicity to lower total cost of ownership, they enable scalable, secure and energy-efficient business operations with intelligent services and a range of advanced Cisco IOS Software features. The Cisco Catalyst 2960-X Series Switches offer the following: 24 or 48 Gigabit Ethernet ports with line-rate forwarding performance Gigabit Small Form-Factor Pluggable (SFP) or 10G SFP+ uplinks FlexStack Plus for stacking of up to 8 switches with 80 Gbps of stack throughput (optional) Power over Ethernet Plus (PoE+) support with up to 740W of PoE budget 24-port PoE fanless switch for deployment outside the wiring closet Reduced power consumption and advanced energy management features USB and Ethernet management interfaces for simplified operations Application visibility and capacity planning with integrated NetFlow-Lite LAN Base or LAN Lite Cisco IOS® software features Enhanced limited lifetime warranty (E-LLW) offering next-business-day hardware replacement Switch Models and Configurations Catalyst 2960-X switches include a single fixed power supply and are available with either the Cisco IOS LAN Base or LAN Lite feature set. Catalyst 2960-XR switch models include a field-replaceable modular power supply and can accommodate a second power supply.Cisco Network Access for Borderless solution focuses on the following primary areas: Power resiliency with optional dual field-replaceable power supplies IP Lite Cisco IOS® software with dynamic routing and Layer 3 features Catalyst 2960-X series Software Features All Catalyst 2960-X Series Switches use a single Universal Cisco IOS Software Image for all SKUs. Depending on the switch model, the Cisco IOS image automatically configures the LAN Lite, LAN Base, or IP Lite feature set. LAN Lite models have reduced functionality and scalability for small deployments with basic requirements. Cisco Catalyst 2960-X Family of Switches are available with the LAN Base and LAN Lite feature sets and Catalyst 2960-XR Family of switches are available IP Lite feature sets. Note that each switch model is tied to a specific feature level; LAN Lite cannot be upgraded to LAN Base and LAN Base cannot be upgraded to IP Lite. Network Security The Cisco Catalyst 2960-X Series Switches provide a range of security features to limit access to the network and mitigate threats, including: MAC-based VLAN assignment enables different users to authenticate on different VLANs. This feature enables each user to have a different data VLAN on the same interface. Cisco TrustSec uses SXP to simplify security and policy enforcement throughout the network. For more information about Cisco TrustSec security solutions Comprehensive 802.1X Features to control access to the network, including Flexible Authentication, 802.1x Monitor Mode, and RADIUS Change of Authorization. IPv6 First-Hop Security enhances Layer-2 and Layer-3 network access from proliferating IPv6 devices especially BYOD devices. It protects against rogue router advertisements, address spoofing, fake DHCP replies and other risks introduced by IPv6 technology. Device Sensor and Device Classifier enable seamless versatile device profiles including BYOD devices. They also enable Cisco Identity Services Engine (ISE) to provision identity based security policies. This feature is available on both the 2960-X and the 2960-XR product families. Cisco Trust Anchor Technology enables easy distribution of a single universal image for all models of Catalyst 2960-X by verifying the authenticity of IOS images. This technology allows the switch to perform IOS integrity checks at boot-up by verifying the signature, verifying the Trusted Asset under Management and authenticating the license. Cisco Threat Defense features including Port Security, Dynamic ARP Inspection, and IP Source Guard. Private VLANs restrict traffic between hosts in a common segment by segregating traffic at Layer 2, turning a broadcast segment into a nonbroadcast multi access like segment. This feature is available in IP-Lite feature set only. Unicast Reverse Path Forwarding (uRPF) feature helps mitigate problems caused by the introduction of malformed or forged (spoofed) IP source address into a network by discarding IP packets that lack a verifiable IP source address. This feature is available in IP-Lite feature set only. Multidomain Authentication allows an IP phone and a PC to authenticate on the same switch port while placing them on appropriate voice and data VLAN. Access Control Lists (ACLs) for IPv6 and IPv4 for security and QoS ACEs. Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3 (SNMPv3) provide network security by encrypting administrator traffic during Telnet and SNMP sessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic software image because of U.S. export restrictions. Switched Port Analyzer (SPAN), with bidirectional data support, allows Cisco Intrusion Detection System (IDS) to take action when an intruder is detected. TACACS+ and RADIUS authentication facilitates centralized control of the switch and restricts unauthorized users from altering the configuration. MAC Address Notification allows administrators to be notified of users added to or removed from the network. Multilevel security on console access prevents unauthorized users from altering the switch configuration. Bridge protocol data unit (BPDU) Guard shuts down Spanning Tree Port Fast-enabled interfaces when BPDUs are received to avoid accidental topology loops. Spanning Tree Root Guard (STRG) prevents edge devices not in the network administrator’s control from becoming Spanning Tree Protocol root nodes. IGMP filtering provides multicast authentication by filtering out nonsubscribers and limits the number of concurrent multicast streams available per port. Dynamic VLAN assignment is supported through implementation of VLAN Membership Policy Server client capability to provide flexibility in assigning ports to VLANs. Dynamic VLAN facilitates the fast assignment of IP addresses. Redundancy and Resiliency Cisco Catalyst 2960-X Series Switches offer a number of redundancy and resiliency features to prevent outages and help ensure that the network remains available: Cross-stack EtherChannel provides the ability to configure Cisco EtherChannel technology across different members of the stack for high resiliency. Flexlink provides link redundancy with convergence time less than 100 milliseconds IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP) provide rapid spanning-tree convergence independent of spanning-tree timers and also offer the benefit of Layer 2 load balancing and distributed processing. Stacked units behave as a single spanning-tree node. Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree reconvergence on a per-VLAN spanning-tree basis, without requiring the implementation of spanning-tree instances. Cisco Hot Standby Router Protocol (HSRP) is supported to create redundant, fail safe routing topologies in 2960-XR IP-Lite SKUs. Switch-port auto-recovery (Error Disable) automatically attempts to reactivate a link that is disabled because of a network error. Power redundancy with an optional second power supply on 2960-XR models, or with an external RPS on 2960-X models. Enhanced Quality of Service The Cisco Catalyst 2960-X Series Switches offers intelligent traffic management that keeps everything flowing smoothly. Flexible mechanisms for marking, classification, and scheduling deliver superior performance for data, voice, and video traffic, all at wire speed. Primary QoS features include: Up to eight egress queues per port and strict priority queuing so that the highest priority packets are serviced ahead of all other traffic. Shaped Round Robin (SRR) scheduling and Weighted Tail Drop (WTD) congestion avoidance. Flow-based rate limiting and up to 256 aggregate or individual policers per port. 802.1p class of service (CoS) and Differentiated Services Code Point (DSCP) classification, with marking and reclassification on a per-packet basis by source and destination IP address, MAC address, or Layer 4 TCP/UDP port number. Cross-stack QoS to allow QoS to be configured across a stack of 2960-X series switches. The Cisco committed information rate (CIR) function provides bandwidth in increments as low as 8 Kbps. Rate limiting is provided based on source and destination IP address, source and destination MAC address, Layer 4 TCP/UDP information, or any combination of these fields, using QoS ACLs (IP ACLs or MAC ACLs), class maps, and policy maps. Cisco Catalyst 2960-X Series Switching Database Manager Switching database manager (SDM) templates for LAN Base and IP Lite licenses allows the administrator to automatically optimize the ternary content-addressable memory (TCAM) allocation to the desired features based on deployment-specific requirements. MAC, routing, security, and QoS scalability numbers depend on the type of template used in the switch. Cisco FlexStack-Plus Cisco FlexStack-Plus provides stacking of up to eight 2960-X switches with the optional FlexStack-Plus module. The FlexStack-Plus module is hot swappable and can be added to any Cisco Catalyst 2960-X or Catalyst 2960-XR with a FlexStack-Plus slot. Switches connected to a stack will automatically upgrade to the stack’s Cisco IOS Software version and transparently join the stack without additional intervention. Cisco FlexStack-Plus and Cisco IOS Software offer true stacking, with all switches in a stack acting as a single switch unit. FlexStack-Plus provides a unified data plane, unified configuration, and single IP address for switch management. The advantages of true stacking include lower total cost of ownership and higher availability through simplified management as well as cross-stack features including EtherChannel, SPAN, and FlexLink. To provide investment protection, FlexStack-Plus is backwards-compatible with FlexStack. Cisco Catalyst 2960-X LAN Base switches equipped with a FlexStack-Plus module can be stacked with Catalyst 2960-S and 2960-SF LAN Base switches equipped with a FlexStack module Power Supply The Catalyst 2960-X switches comes with one fixed power-supply and options for an external redundant power supply source (RPS2300). The Catalyst 2960-XR switches support dual redundant power supplies. The Catalyst 2960-XR ships with one power supply by default. The second power supply can be purchased at the time of ordering the switch or as a spare. These power supplies have in-built fans to provide cooling. Intelligent Power over Ethernet Plus Cisco Catalyst 2960-Xseries switches support both IEEE 802.3af Power over Ethernet (PoE) and IEEE 802.3at PoE+ (up to 30W per port) to deliver lower total cost of ownership for deployments that incorporate Cisco IP phones, Cisco Aironet wireless access points, or other standards-compliant PoE/PoE+ end devices. PoE removes the need to supply wall power to PoE-enabled devices and eliminates the cost of adding electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. The Catalyst 2960-X series PoE power allocation is dynamic and power mapping scale up to a maximum of 740W PoE+ power. The 2960-XR switch configurations offer the additional benefit of dual redundant power supplies. If both power supplies are used, then the 2960-XR shares the load between the two power supplies for non stop power. Power Management The 2960-X switches offer a range industry leading features for effective energy efficiency and energy management. 2960-X Series are the greenest switches in the industry. Switch Hibernation Mode (SHM) is an industry first and available on all 2960-X series switches. This feature puts the switch in ultra low power mode during periods of non-operation such as nights or weekends. Switch Hibernation Mode on the 2960-X switches can be scheduled using EnergyWise compliant management software. IEEE 802.3az EEE (Energy Efficient Ethernet) enables ports to dynamically sense idle periods between traffic bursts and quickly switch the interfaces into a low power idle mode, reducing power consumption. Cisco EnergyWise policies can be used to control the power consumed by PoE-powered endpoints, desktop and data-center IT equipment, and a wide range of building infrastructure. EnergyWise technology is included on all Cisco Catalyst 2960-X Series Switches. Power Management The Cisco Catalyst 2960-X Series adds a new member to its 2960-X family, the WS-C2960X-24PSQ-L (Cool). This is a 24-port 10M/100M/1000M switch that can power up to 8 ports of PoE (first eight ports only) with ability to deliver a sum total of 110W of PoE power. This switch has four Gigabit Ethernet uplinks: two of them SFP and the other two 10M/100M/1000M copper interfaces enabling choice of fiber or copper connectivity to the aggregation point. Some important 2960-X “cool” switch highlights are: Extends a highly secure, intelligent, managed Cisco Catalyst infrastructure with a single Ethernet cable or fiber from the wiring closet. Support for advanced security and intelligent services, including Netflow-Lite and Switch Hibernation, including voice, video, AP powering, and Cisco Enterprise Network services to remote endpoints Less than 12” depth fit in user work spaces where multiple cable runs could be challenging with very low power consumption and heat dissipation Higher MTBF rates due to no moving mechanical parts, no fans help ensure that 2960X cool switch is convenient to be used for colocated applications Easy to deploy using smart-install, configure with auto-smart-ports and device sensors and manage using Cisco Prime or CNA Cisco Enhanced Limited Lifetime Hardware Warranty Cisco Catalyst 2960-X Series Switches come with an enhanced limited lifetime warranty (E-LLW). The E-LLW provides the same terms as Cisco’s standard limited lifetime warranty but adds next business day delivery of replacement hardware, where available, and 90 days of 8X5 Cisco Technical Assistance Center (TAC) support. Your formal warranty statement, including the warranty applicable to Cisco software, appears in the Cisco information packet that accompanies your Cisco product. We encourage you to review carefully the warranty statement shipped with your specific product before use.
SKU: WS-C2960XR-48FPS-I - Switches
Cisco Catalyst WS-C2960-24TT-L Switch 24 Ports Managed Rack Mountable
0 out of 5(0)General Specifications Manufacturer Cisco Manufacturer Part # WS-C2960-24TT-L Manufacturer UPC # 0882658044113 Product Description Cisco Catalyst 2960-24TT – Switch – managed – 24 x 10/100 + 2 x 10/100/1000 – rack-mountable Device Type Switch – 24 ports – managed Enclosure Type Rack-mountable 1U Interfaces Fast Ethernet Ports 24 x 10/100 + 2 x 10/100/1000 Performance Switching capacity : $52 (32 Gbp)s Forwarding performance (64-byte packet size) : 6.5 Mpps MAC Address Table Size 8K entries Remote Management Protocol SNMP 1, SNMP 2, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, HTTPS, TFTP, SSH Features Layer 2 switching, auto-sensing per device, dynamic IP address assignment , auto-negotiation, BOOTP support, ARP support, load balancing, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, Syslog support, DiffServ support, Broadcast Storm Control, IPv6 support, Multicast Storm Control, Unicast Storm Control, Rapid Spanning Tree Protocol (RSTP) support, Multiple Spanning Tree Protocol (MSTP) support, DHCP snooping, Dynamic Trunking Protocol (DTP) support, Port Aggregation Protocol (PAgP) support, Access Control List (ACL) support, Quality of Service (QoS), Link Aggregation Control Protocol (LACP), Port Security, MAC Address Notification, Remote Switch Port Analyzer (RSPAN) Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ab (LLDP) Power AC 120/230 V ( 50/60 Hz ) Approximate Dimensions (WxDxH) 17.5 in x 9.3 in x 1.7 in Approximate Weight 8 lbs Manufacturer Warranty Limited lifetime warranty Brief Overview Catalyst 2960 Series Switch 24 ports – managed Rack-mountable 1U 8K entries Switching capacity Cisco Catalyst 2960 Series Intelligent Ethernet Switches are a new family of fixed-configuration standalone devices that provide desktop Fast Ethernet and Gigabit Ethernet connectivity, enabling enhanced LAN services for entry-level enterprise, mid-market, and branch office networks. The Catalyst 2960 Series offers integrated security, including network admission control (NAC), advanced quality of service (QoS), and resiliency to deliver intelligent services for the network edge. Cisco Catalyst 2960 Series Overview: The Cisco Catalyst 2960 Series Switches are the leading Layer 2 edge, providing improved ease of use, highly secure business operations, improved sustainability, and a borderless network experience. The Catalyst 2960-S Series Switches include new FlexStack switch stacking capability with 1 and 10 Gigabit connectivity, and Power over Ethernet Plus (PoE+) with the Cisco Catalyst 2960 Series Switches offering Fast Ethernet access connectivity and PoE capabilities. The Cisco Catalyst 2960 Series are fixed-configuration access switches designed for enterprise, midmarket, and branch office networks to provide lower total cost of ownership. The Cisco Catalyst 2960 Series Switches with LAN Base Software offer the following: Dual-purpose uplinks for Gigabit Ethernet uplink flexibility, allowing use of either a copper or fiber uplink; each dual-purpose uplink port has one 10/100/1000 Ethernet port and one SFP-based Gigabit Ethernet port, with one port active at a time. 24 or 48 ports of Fast Ethernet desktop connectivity. PoE configurations with up to 15.4W per port. A wide range of software features to provide ease of operation, highly secure business operations, sustainability, and a borderless networking experience. Cisco Catalyst 2960 Series Switches Enable Cisco Borderless Network Borderless Networks, a Cisco architecture, deliver the new workspace experience, connecting anyone, anywhere, using any device, to any resource securely, reliably, and transparently. Cisco’s Borderless Networks architecture addresses primary IT and business challenges to help create a truly borderless experience by bringing interactions closer to the employee and customer. Borderless experience is only possible with intelligent network elements designed and architected to meet the needs of a global workspace. Cisco Network Access is a primary component of this architecture, enabling various borderless network services such as mobility, security, sustainability, EnergyWise and ease of operations for increased productivity and operational efficiency. When network access is intelligent, it knows the identity of the user, as well as where the user is on the network. It knows what is connecting to the network, to automatically provision the network for QoS and delivery. It becomes services-aware to optimize user experience. Only with intelligent access network, your enterprise can go borderless securely and transparently. Your business can save energy, simplify operations with better business efficiency, and have an optimized total cost of ownership.Cisco Network Access for Borderless solution focuses on the following primary areas: Sustainability EnergyWise Ease of operations Borderless security Borderless experience Sustainability Cisco Catalyst switching solutions enable greener practices through measurable power efficiency, integrated services, and continuous innovations such as Cisco EnergyWise, an enterprise wide solution that monitors and conserves energy with customized policies. Together, Cisco EnergyWise technology and Cisco Catalyst switches reduce greenhouse gas (GhG) emissions and increase energy cost savings and sustainable business behavior. Sustainability features in the Cisco Catalyst 2960 Series Switches include the following features sets: Cisco EnergyWise technology Efficient switch operation Intelligent power management Cisco EnergyWise Technology Cisco EnergyWise is an innovative architecture, added to fixed configuration switches, promoting company wide sustainability by reducing energy consumption across an entire corporate infrastructure and affecting more than 50percent of global greenhouse gas emissions created by worldwide building infrastructure, a much greater effect than the 2 percent generated by the IT industry. Cisco EnergyWise enables companies to measure the power consumption of network infrastructure and network-attached devices and manage power consumption with specific policies, reducing power consumption to realize increased cost savings, potentially affecting any powered device. Efficient Switch Operation Cisco Catalyst 2960 Series Switches, designed and engineered by Cisco, provide optimum power savings, low power operations for industry best-in-class power management, and power consumption capabilities. The Catalyst 2960-S ports are capable of reduced power modes so that ports not in use can move into a lower power utilization state. Intelligent Power over Ethernet Management The Cisco Catalyst 2960-S PoE models support the latest PoE+ devices including Cisco IP phones and Cisco Aironet WLAN access points providing up to 30W of power per port, as well as any IEEE 802.3af-compliant end device. Per port power consumption command allows customers to specify maximum power setting on an individual port Per port PoE power sensing measures actual power being drawn, enabling more intelligent control of powered devices Cisco Discovery Protocol Version 2 allows switches to negotiate a more granular power setting when connecting to a Cisco powered device such as IP phones or access points than what is provided by IEEE classification The PoE MIB provides proactive visibility into power usage and allows customers to set different power-level thresholds Ease of Operations The Cisco Catalyst 2960 Series Switches help reduce the operating costs through: Cisco Catalyst Smart Operations Easy to use deployment and control features Advanced, intelligent network management tools Cisco Catalyst Smart Operations Cisco Catalyst Smart Operations is a comprehensive set of capabilities that simplify LAN deployment, configuration, and troubleshooting. Cisco Catalyst Smart Operations enable zero touch installation and replacement of switches, fast upgrade, as well as ease of troubleshooting with reduced operational cost. Cisco Catalyst Smart Operations is a set of features that includes Smart Install, Auto Smartports, Smart Configuration, and Smart Troubleshooting to enhance operational excellence: Cisco Smart Install is a transparent plug-and-play technology to configure the Cisco IOS Software image and switch configuration without user intervention. Smart Install utilizes dynamic IP address allocation and the assistance of other switches to facilitate installation providing transparent network plug and play. Cisco Auto Smartports provide automatic configuration as devices connect to the switch port, allowing auto detection and plug and play of the device onto the network. Cisco Smart Configuration provides a single point of management for a group of switches and in addition adds the ability archive and backup configuration files to a file server or switch allowing seamless zero touch switch replacement. Cisco Smart Troubleshooting is an extensive array of debug diagnostic commands and system health checks within the switch, including Generic Online Diagnostics (GOLD) and on board Failure Logging (OBFL). Easy to Use Deployment and Control Features Automatic QoS (AutoQoS) simplifies QoS configuration in voice over IP (VoIP) networks by issuing interface and global switch commands to detect Cisco IP phones, classify traffic, and help enable egress queue configuration. Stacking Master configuration management and Cisco FlexStack stacking helps ensure that all switches are automatically upgraded when the master switch receives a new software version. Automatic software version checking and updating help ensure that all stack members have the same software version. Dynamic Host Configuration Protocol (DHCP) auto configuration of multiple switches through a boot server eases switch deployment. Auto-negotiation on all ports automatically selects half- or full-duplex transmission mode to optimize bandwidth. Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch ports. Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel® groups or Gigabit EtherChannel groups to link to another switch, router, or server. Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP. Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and receive pairs if an incorrect cable type (crossover or straight-through) is installed. Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional links caused by incorrect fiber-optic wiring or port faults to be detected and disabled on fiber-optic interfaces. Switching Database Manager (SDM) templates for access, routing, and VLAN deployment allow the administrator to easily maximize memory allocation to the desired features based on deployment-specific requirements. Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN Edge to minimize broadcasts and maximize available bandwidth. Internet Group Management Protocol (IGMP) Snooping for IPv4 and IPv6 MLD v1 and v2 Snooping provide fast client joins and leaves of multicast streams and limit bandwidth-intensive video traffic to only the requestors. Multicast VLAN Registration (MVR) continuously sends multicast streams in a multicast VLAN while isolating the streams from subscriber VLANs for bandwidth and security reasons. Per-port broadcast, multicast, and unicast storm control prevents faulty end stations from degrading overall systems performance. Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN for easier administration and troubleshooting. Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk configuration across all switch. Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a Layer 2 switch network from any other switch in the same network. For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring (RMON) software agent supports four RMON groups (history, statistics, alarms, and events). Layer 2 traceroute eases troubleshooting by identifying the physical path that a packet takes from source to destination. Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by downloading from a centralized location. Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet switches. Advanced, Intelligent Network Management Tools The Cisco Catalyst 2960 Series Switches offer both a superior CLI for detailed configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates. In addition, CiscoWorks LAN Management Solution (LMS) supports the Cisco Catalyst 2960 Series Switches for networkwide management. Cisco Network Assistant A PC-based network management application designed for small and medium-sized business (SMB) networks with up to 250 users, Cisco Network Assistant offers centralized network management and configuration capabilities. Cisco Network Assistant uses Cisco Smartports technology to simplify both initial deployment and ongoing maintenance. This application also features an intuitive GUI where users can easily apply common services across Cisco switches, routers, and access points, such as: Configuration management Troubleshooting advice Inventory reports Event notification Network security settings Password synchronization Drag-and-drop Cisco IOS Software upgrades Secure wireless Enhanced Quality of Service The Cisco 2960 Series Switches offers intelligent services that keep everything flowing smoothly. Industry-leading mechanisms for marking, classification, and scheduling deliver superior performance for data, voice, and video traffic, all at wire speed. Following are some of the QoS features supported in the Cisco 2960 Series Switches: Cross-stack QoS allows QoS to be configured across the entire Cisco 2960-S Flexstack. 802.1p class of service (CoS) and differentiated services code point (DSCP) field classification are provided, using marking and reclassification on a per-packet basis by source and destination IP address, MAC address, or Layer 4 TCP/UDP port number. Cisco control-plane and data-plane QoS ACLs on all ports help ensure proper marking on a per-packet basis. Four egress queues per port help enable differentiated management of different traffic types across the stack. Shaped Round Robin (SRR) scheduling helps ensure differential prioritization of packet flows by intelligently servicing the ingress queues and egress queues. Weighted Tail Drop (WTD) provides congestion avoidance at the ingress and egress queues before a disruption occurs. Strict priority queuing helps ensure that the highest-priority packets are serviced ahead of all other traffic. Trusted Boundary provides the ability to trust the QoS priority settings if an IP phone is present and to disable the trust setting if the IP phone is removed, thereby preventing a malicious user. Rate limiting is provided based on source and destination IP address, source and destination MAC address, Layer 4 TCP/UDP information, or any combination of these fields, using QoS ACLs (IP ACLs or MAC ACLs), class maps, and policy maps. Up to 64 aggregate or individual policers are available per Fast Ethernet or GbE port. Location Awareness and Mobility In order to provide delivery of a best-in-class network experience to end users, it’s critical for network access to be location aware. A wide variety of devices can appear on the network, both wired (switches, routers, IP phones, PCs, access points, controllers, video digital media players, and so on) and wireless (mobile devices, wireless tags, rogues, and so on). In many industries, locating assets is primarily a manual process and is time consuming and error prone. The inability to locate assets in real time and to help ensure their availability when and where they are needed limits reaction time and efficiency. Location services answer business-critical questions about both mobile assets and the users of those assets regardless of whether those assets are connecting using wired or wireless, and hence directly improve their organization’s profitability. Network Location Services also improve security and accelerate client troubleshooting by locating an asset, user, or device on the network. Network visibility and control provide centralized visibility into wired and wireless devices on the network and their location. Location-assisted client troubleshooting enables tracking of wired or wireless clients for quick problem resolution. Asset tracking and improved security provide centralized inventory of wired and wireless devices and asset management for improved business processes. Location based policy allows greater control and visibility. With EnergyWise, power policies can be set up (to reduce the power or shut down the power from a port) based on the location. Cisco Emergency Responder (CER) enhances emergency calling from Cisco Unified CallManager. It helps assure that Cisco Unified CallManager sends emergency calls to the appropriate Public Safety Answering Point (PSAP) for the caller’s location.
SKU: WS-C2960-24TT-L